Search Results

Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series

2019-08-07

CURRENT

J174_201908

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.

Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series

2013-04-11

HISTORICAL

J174_201304

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.

Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series

2013-04-11

HISTORICAL

J174M_201304

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.

Standard

Blind Rivets - Break Mandrel Type

2013-04-15

HISTORICAL

J1200_201304

This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.

Standard

Surface Discontinuities on Nuts

1998-05-01

HISTORICAL

J122_199805

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts, in sizes 6.3 to 25 mm and inch-series nuts in sizes 1/4 to 1 in, inclusive, which are primarily intended for use in automotive assemblies.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2016-11-18

CURRENT

J1053M_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2013-04-11

HISTORICAL

J1053M_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Standard

STEEL STAMPED NUTS OF ONE PITCH THREAD DESIGN

1973-08-01

HISTORICAL

J1053_197308

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE Standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. It should be noted that stamped nuts having other sizes and configurations are available and manufacturers should be consulted.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2016-11-18

CURRENT

J1053_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

STEEL STAMPED NUTS OF ONE PITCH THREAD DESIGN—INCH SERIES

1996-08-01

HISTORICAL

J1053_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2013-04-11

HISTORICAL

J1053_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

Surface Discontinuities on General Application Bolts, Screws, and Studs

2012-11-19

CURRENT

J1061_201211

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

Tension Indicating Washer Tightening Method for Fasteners

2018-04-24

CURRENT

J2486_201804

This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.

Standard

Tension Indicating Washer Tightening Method for Fasteners

2013-04-15

HISTORICAL

J2486_201304

This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.

Standard

Tension Indicating Washer Tightening Method for Fasteners

1999-05-01

HISTORICAL

J2486_199905

This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.

Standard

Nut and Conical Spring Washer Assemblies

2013-04-15

HISTORICAL

J238_201304

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Standard

Nut and Conical Spring Washer Assemblies

2017-05-30

CURRENT

J238_201705

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Standard

Dryseal Pipe Threads

2013-02-01

CURRENT

J476_201302

The Dryseal American Standard Taper Pipe Thread, the Dryseal American Fuel Internal Straight Pipe Thread and the Dryseal American Intermediate Internal Straight Pipe Thread covered by this standard conform with the American Standard ASA-B2.2. The Dryseal SAE-Short Taper Pipe Thread in this standard conforms with the Dryseal American Standard Taper Pipe Thread except for the length of thread, which is shortened for increased clearance and economy of material. The significant feature of the Dryseal thread is controlled truncation at the crest and root to assure metal to metal contact coincident with or prior to flank contact. Contact at the crest and root prevents spiral leakage and insures pressure-tight joints without the use of a lubricant or sealer. Lubricants, if not functionally objectionable, may be used to minimize the possibility of galling in assembly.

Standard

Steel Self-Drilling Tapping Screws

2021-07-28

CURRENT

J78_202107

This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications having point Styles 2, 3, 4, and 5. It is the objective of this document to ensure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly.

Standard

Steel Self-Drilling Tapping Screws

2013-04-16

HISTORICAL

J78_201304

This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.